超精密气体静压系统节流器法向随机微振动研究

以无气腔平面节流器为研究对象,对节流器流固耦合法向随机微振动进行了理论仿真和实验研究。受限于节流器厚度与气膜厚度尺寸的差异和输入初始边界条件,建立了节流器的COMSOL仿真简化模型,对节流器-气膜微流场进行双向流固耦合数值模拟。仿真结果表明,节流器的法向随机微振动幅值关于节流器中心对称,且由中心向边缘逐渐增大;微振动幅值随气体入口流速的增大而增大。实验采用纳米级激光测振仪,依次测量供气压力为0.1,0.2,…,0.5 MPa时尺寸为75 mm×50 mm×14 mm的HEXAGON双环联结型节流器多个不同位置的法向振动,实验结果表明,法向随机微振动幅值分布特性与仿真结果一致,关于节流器中心对称,且由中心向边缘逐渐增大,验证了节流器法向微振动的"跷跷板"振动形式;在0.5 MPa供气压力下,边缘振动幅值超过1 nm。对实验数据进行功率谱密度分析,结果表明不同供气压力下法向随机微振动均在9.4 kHz和10.6 kHz处产生较大功率,可认为与节流器-气膜流固耦合系统的固有频率有关。研究结果有效地揭示了节流器法向随机微振动的特性,为气体静压系统避开随机共振区、优化气体静压系统的设计提供了理论指导。     

朝凯煤矿露天台阶爆破装药结构优化应用研究

本文以神达朝凯煤矿正在开采的台阶为工程背景,针对该矿在台阶爆破过程中存在着大块率高、根底多的现象,通过改变装药结构的方式对爆破参数进行优化。实践证明,优化后大块率和根底问题的治理效果明显。     

单一低渗透突出煤层水力冲孔工艺优化应用分析

为了有效提高单一低渗透突出煤层的瓦斯抽采效率，以高压水射流冲击理论为指导，针对平煤股份八矿己组突出煤层特征建立数值模型，模拟分析水力冲孔应力分布规律，通过现场实测分析冲孔有效影响范围，进一步优化设计冲孔参数、指导现场施工。现场应用表明，水力冲孔是一种行之有效的方法，对单一低渗透突出煤层实施水力冲孔卸压增透、提高瓦斯抽采效果具有重要意义。     

Flow visualization of Rayleigh–Bénard convection for cubical cavity

Natural convective flow of air inside the cubical cavity is investigated numerically. The temperature of the bottom wall is kept higher than that of top cold wall, and other four walls are assumed to be adiabatic. Attention has been paid to the convective discretization schemes, like upwind, QUICK, total variation diminishing, normalized variable diagram (NVD) schemes that are compared with respect to accuracy. The output is validated with respect to the results available in the literature. A parallel computing message passing interface code is adapted to run the simulations. From the results, it is observed that the NVD scheme gives better results among all the employed convective discretization schemes irrespective of the mesh structure. Thus, in this article, self filtered central differencing which is a family of NVD, is used. From the enormous output data, along with the streamlines, contours of isotherms, the new technique of energy pathlines, and field synergy are used to visualize the fluid flow and heat transfer mechanism arising in the system in the range of Ra from 10³ to 10⁶. Free energy streamlines are observed with small Ra, whereas trapped energy streamlines are observed with high Ra. When Ra increases, synergy angle increases and implies that the synergy between the velocity vector and temperature gradient gets reduced and leads to increasing values of average Nusselt number (Nu).     

Effect of clad ratio on interfacial microstructure and properties of cladding billets via direct-chill casting process

Numerical simulation and experiments were introduced to develop AA4045/AA3003 cladding billets with different clad-ratios. The temperature fields, microstructures and mechanical properties near interface were investigated in detail. The results show that cladding billets with different clad-ratios were fabricated successfully. Si and Mn elements diffused across the bonding interface and formed diffusion layer. With the increase of clad-layer thickness, the interfacial region transforms from semisolid–solid state to liquid–solid state and the diffusion layer increased from 10 to 25 μm. The hardness at interface is higher than that of AA3003 side but lower than that of the other side. The bonding strength increased with the clad-layer thickness, attributing to solution strengthening due to elements diffusion. The cladding billets were extruded into clad pipe by indirect extrusion process after homogenization. The clad pipe remained the interfacial characteristics of as-cast cladding billet and the heredity of clad-ratio during deformation was testified.     

Cutting parameter optimization for one-step shaft excavation technique based on parallel cutting method

The outcome of the cutting blasting in a one-step shaft excavation is heavily related to the cutting parameters used for parallel cutting method. In this study, the relationships between the cutting parameters (such as the hole spacing L and the empty hole diameter D) and damage zones were investigated by numerical simulation. A damage state index γ was introduced and used to characterize the crushing and crack damage zones through a user-defined subroutine. Two indices, i.e., η₁ and η₂ that can reflect the cutting performance, were also introduced. The simulation results indicate that an optimal value of L can be obtained so that the η₁ and η₂ can reach their optimal states for the best cutting performance. A larger D results in better cutting performance when the L value maintains its best. In addition, the influences of the loading rate and the in-situ stress on the cutting performance were investigated. It is found that an explosive with a high loading rate is suit for cutting blasting. The propagation direction and the length of the tensile cracks are affected by the direction and the magnitude of the maximum principal stress.     

LTE室分高倒流小区解决方案的研究

LTE室分高倒流直接影响室内4G用户的感知，同时较大程度拉低LTE网络驻留率指标。由于室内无线环境的封闭性，室分小区之间的覆盖独立性，仅仅通过参数调整的手段达到降低高倒流的效果非常不明显，因此本文针对目前影响室内用户感知的高倒流问题，从高倒流小区的标准出发，对室分高倒流小区的发现手段，产生原因及解决方案进行详尽地阐述，并针对各类型的高倒流情形提出解决方法，最终提供读者发现、分析及解决室分高倒流小区的有效方案，从而作为研究方法提供给LTE室内小区高倒流问题解决的指导意见     

浅谈煤与瓦斯突出矿井"U"型通风系统采煤工作面上隅角瓦斯管理

屯兰煤矿是煤与瓦斯突出矿井,瓦斯涌出量大,上隅角瓦斯治理困难。为解决这一通风难题,该矿采取沿空留巷抽采措施进行作业。实践证明,该技术解决了上隅角瓦斯积聚隐患,保障了矿井高产高效。